Delta Tau GEO PMAC User Manual Page 22
- Page / 117
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Geo PMAC Drive User Manual
12 Specifications
GxH012 GxH032 GxH052 GxH102 GxH152
Output Circuits (axes)
2
Nominal Input Voltage (VAC)
480
Rated Input Voltage (VAC)
300-525
Rated Continuous Input Current (A
AC
RMS
)
1.98 3.96 6.6 13.2 19.8
Rated Input Power (Watts)
1646 3292 5487 10974 16461
Frequency (Hz)
50/60
Phase Requirements
1Φ or 3Φ 3Φ
Charge Peak Inrush Current (A)
Main
Input
Power
Main Bus Capacitance (µf)
845 1255
Rated Output Voltage (V) @ Rated
Current
288
Rated Cont. Output Current per Axis
1.5 3 5 10 15
Peak Output Current (A) for 2 seconds
4.5 9 10 20 30
Rated Output Power per Axis (Watts)
748 1496 2494 4988 7482
Nominal DC Bus
678
Over-voltage Trip Level (VDC)
828
Bus
Protection
Under-voltage Lockout Level (VDC)
20
Turn-On Voltage (VDC)
784
Turn-Off Voltage (VDC) 744
Shunt
Re
g
ulator
Ratings
Delta Tau Recommended Load Resistor
(300 W Max.)
GAR78 GAR48
Input Voltage (VDC)
20-27
Input Current (A)
2A
Control
Lo
g
ic
Power
Inrush Current (A)
4A
Resolution (bits)
12
Current
Feedback
Full-scale Signed Reading (±Amperes)
7.32 14.64 16.26 32.53 48.79
Delta Tau Recommended PWM
Frequency (KHz) @ rated current
12 10 8
Minimum Dead Time (µs)
1.6
Transistor
Control
Charge Pump Time (% of PWM period.)
5
Note:
All values at ambient temperature of 0-45°C (113F) unless otherwise stated.
- ^2 Geo PMAC Drive 1
- Copyright Information 3
- Operating Conditions 3
- Safety Instructions 3
- WARNING: 4
- REVISION HISTORY 5
- .......61 8
- INTRODUCTION 11
- Geo PMAC Drives 12
- Feedback Devices 13
- Compatible Motors 13
- Motor Poles 14
- Introduction 5 15
- 6 Introduction 16
- SPECIFICATIONS 17
- Geo PMAC Feedback Options 18
- Package Types 18
- Electrical Specifications 19
- 480VAC Input Drives 21
- Environmental Specifications 23
- 14 Specifications 24
- RECEIVING AND UNPACKING 25
- 16 Receiving and Unpacking 26
- MOUNTING 27
- Geo PMAC 28
- Low Profile, Dual Axis 28
- GIL012XX, GIH012XX 28
- Single Width 29
- GIH102, GIL152 & GIH152 30
- Double wide with 2 Fans 30
- CONNECTIONS 31
- Use of GFI Breakers 32
- Noise Problems 32
- Operating Temperature 32
- Single Phase Operation 32
- Wiring AC Input, J1 33
- Wiring Earth-Ground 33
- Wiring the Motors 34
- Wiring the Motor Thermostats 35
- Shunt Regulation 37
- Minimum Resistance Value 37
- Maximum Resistance Value 37
- Energy Transfer Equations 37
- 28 System Wiring 38
- System Wiring 29 39
- Bonding 40
- Filtering 40
- Motor Line Filtering 41
- I/O Filtering 41
- System Wiring 42
- CONNECTORS 43
- X2: Encoder Input 2 44
- 6 5 123479 8 45
- 12 11 1 0 45
- Connectors 46
- Connectors 37 47
- TB-4: 016-P L0F04-38P 48
- X8: S. Encoder 1 49
- X9: S. Encoder 2 51
- X10: Discrete I/O 52
- Connectors 43 53
- SETTING UP THE ENCODERS 56
- Setting up SSI Encoders 57
- Software Setup 58
- SSI Clock Frequency 58
- Expected Data Format 58
- Word Length 58
- Direct Memory Write Example 59
- Setting Up Encoders 60
- Commutation Example 1 61
- Commutation Example 2 61
- Encoder Connections 62
- Hardware Setup 62
- Principle of Operation 64
- Setting Up Encoders 55 65
- Setting up EnDat Interface 66
- Setting up Resolvers 69
- Range: 0 – 255 71
- Signal Format 72
- Hall Sensors 73
- Hall Sensors at 0 75
- Using the Test Results 80
- 72 Setting up Encoders 82
- Encoder Loss Setup 83
- Application Safe 84
- ; is a fault 85
- Key Servo IC Variables 86
- Key Motor Variables 86
- DC BRUSH MOTOR DRIVE SETUP 88
- Hardware Connection 89
- SETTING I 90
- T PROTECTION 90
- Setting I 91
- T Protection 81 91
- TROUBLESHOOTING 95
- Status LEDs 96
- APPENDIX A 97
- CONKIT1A 98
- CONKIT1C 99
- CONKIT2A 99
- CONKIT2C 99
- CONKIT4A 99
- Cable Drawings 100
- Geo PMAC Drive User Manual 101
- Appendix A 91 101
- Geo PMAC Drive User Manual 102
- 92 Appendix A 102
- Appendix A 93 103
- 94 Appendix A 104
- Appendix A 95 105
- √ √ √ 106
- √ √ 106
- √ √ 106
- Appendix A 97 107
- 98 Appendix A 108
- APPENDIX B 109
- LIMITS n 110
- APPENDIX C 111
- 102 Appendix C 112
- Appendix C 103 113
- 104 Appendix C 114
- Appendix C 105 115
- 106 Appendix C 116
- MEMORY AND I/O MAP ADDENDUM 117
Related products and manuals for Noise Reduction Machine Delta Tau GEO PMAC
(51 pages)© 2020, manymanuals.com. All rights reserved. | 1.254 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals